EA-MOIP-12D-100

Front Panel

Status LED — Glows Blue when the amp is on. When the LED is off the amp is in standby or not connected to power.
Channel LEDs — Shows the configuration status of channel.
- Blue — Channel is being used in a configured zone.
- Off — Channel is not configured for use in a zone.
- Red — Channel is in fault status over temperature or over current.

Power switch — Powers the amplifier on or off.
Sub Out (×6) — Low-level RCA loop outs to pair with a subwoofer in 2.1 and 5.1 systems, with adjustable crossover.
Analog Input (×2) — Dual RCA (L/R) inputs to connect outputs from any analog stereo source across any or all channels.
Digital Input (Coax/Optical combo) — Amplify outputs from any digital source across any or all channels. (See playback format for supported formats)
Reset button — Press and hold for 10 seconds to reset the address the amp receives from the MoIP controller.
Network (RJ45) — Ethernet input to connect the amplifier to the network. A CAT-6E cable or better is recommended.
Power input — Connect to power using the supplied power cable.
Fuse — T6.3AH, 200V
Speaker outputs — Low impedance speaker outputs (1× 4-pin Phoenix connector)

Status LED — Glows Blue when the amp is on. When the LED is off the amp is in standby or not connected to power.
Channel LEDs — Shows the configuration status of channel.
- Blue — Channel is being used in a configured zone.
- Off — Channel is not configured for use in a zone.
- Red — Channel is in fault status over temperature or over current.

Speaker outputs — Low impedance speaker outputs (1× 6-pin Phoenix connector).
Sub Out (×3) — Low-level RCA loop outs to pair with a subwoofer in 2.1 and 5.1 systems, with adjustable crossover.
Analog Input — Dual RCA (L/R) input to connect outputs from any analog stereo source across any or all channels.
Digital Input (Coax/Optical combo) — Amplify outputs from any digital source across any or all channels. (See playback format for supported formats)
Reset button — Press and hold for 10 seconds to reset the address the amp receives from the MoIP controller.
Network (RJ45)/PoE Input — Ethernet input to connect the amplifier to the network. The unit can also accept PoE / PoE+ / PoE++ via this port. CAT-6E cable or better is recommended.
48V DC Input — When PoE power supply is not available, the unit can be powered via the optional EE-PS-48V-2.5A external power supply.

Status LED — Glows Blue when the amp is on. When the LED is off the amp is in standby or not connected to power.
Channel LEDs — Shows the configuration status of channel.
- Blue — Channel is being used in a configured zone.
- Off — Channel is not configured for use in a zone.
- Red — Channel is in fault status over temperature or over current.

Speaker outputs — Low impedance speaker outputs (1× 6-pin Phoenix connector).
Sub Out — Low-level RCA loop out to pair with a subwoofer in 2.1 and 5.1 systems, with adjustable crossover.
Analog Input — Dual RCA (L/R) input to connect outputs from any analog stereo source across any or all channels.
Digital Input (Coax/Optical combo) — Amplify outputs from any digital source across any or all channels. (See playback format for supported formats).
Reset button — Press and hold for 10 seconds to reset the address the amp receives from the MoIP controller.
Network (RJ45) / PoE Input — Ethernet input to connect the amplifier to the network. The unit can also accept PoE / PoE+ / PoE++ via this port. CAT-6E cable or better is recommended.
48V DC Input — When PoE power supply is not available, the unit can be powered via the optional E EE-PS-48V-2.5A external power supply.